Skip to main content
24/7 Emergency(602) 675-1555

Hydro Jetting in Phoenix

Clean the whole pipe, not just the clog. Camera first, pressure matched to your line, and a second look to prove it is clear. Homes, restaurants and commercial buildings.

The Short Version

Clean the Pipe, Not Just the Clog

HQ Plumbing & Air does hydro jetting in Phoenix for drain and sewer lines in homes, restaurants and commercial buildings, from Downtown and North Central Phoenix to East, South and West Phoenix, Ahwatukee and the rest of the Valley. We run a camera first, match the pressure to the pipe, and look again after the cleaning, so you see the line is clear.

A snake pokes a hole through a clog and leaves the grease, scale and root hairs on the pipe wall. Hydro jetting uses a pump, a hose and a nozzle to scour the whole inside of the pipe, so the line runs close to its full size again. It is the right tool for clogs that keep coming back, grease, roots and heavy buildup. Read what hydro jetting is for the full explanation.

It is not right for every pipe. Old or broken lines can be damaged by pressure, so we look first and tell you honestly if jetting is the wrong call. The estimate is free and the price is upfront. Licensed and insured, with 24/7 emergency service.

Clean the Pipe, Not Just the Clog
What It Clears

What Hydro Jetting Removes

Hardened grease and cooking oil buildup
Sludge, sediment and mineral scale
Food solids and paper debris
Soap scum and hair
Tree roots growing into the pipe
Sand, silt and storm debris
How It Works

How a Jetting Job Works

  1. Look first

    A camera goes in to find the cause, the location and the pipe material. Then we decide whether the pipe can take jetting.
  2. Match the setup

    Pressure and flow are chosen for the pipe size and the blockage, with a nozzle to suit. We open the line at a cleanout when there is one.
  3. Jet the line

    The nozzle scours the pipe wall and flushes the debris downstream and out, so it does not settle into a new clog.
  4. Look again

    A second camera pass shows the result. You get the findings explained, and if the pipe needs repair we quote it separately.
Pipe Safety

Why We Look Before We Jet

Pressure cleans, and pressure can also break a weak pipe. Spartan Tool, a maker of jetting equipment, notes that pressure has to be matched to the pipe, and warns that too much in a small line can tear a clay tile line apart or separate the hubs on cast iron. Pressure is only half the setup: flow, the gallons per minute, is what carries the loosened debris out of the line.

That is why the camera comes first. It shows whether the pipe is sound, cracked, sagging or made of a material that cannot be cleaned this way. Fiber pipe such as Orangeburg tears under mechanical cleaning. Aging cast iron may call for a gentler approach. When jetting is the wrong tool, we say so and quote the right one.

Older Phoenix Homes

Is Hydro Jetting Safe for an Older Home?

Often it is, once the camera shows the pipe is sound. Census figures show about 4 in 10 Phoenix homes were built before 1980, and roughly 92,000 before 1960 (Census ACS, year structure built). Homes that age in Arcadia, Maryvale, Sun City and the older parts of Central Phoenix often still drain through cast iron or clay. Cast iron scales up inside and can rust thin at the bottom of the pipe. Clay joints open up and let roots in.

A pipe like that can still be jetted, but not the same way as new plastic pipe. When the camera shows heavy scale on sound cast iron, we match the pressure, the flow and the nozzle to that pipe. When it shows a broken joint, a crushed section or fiber pipe, we stop, show you the footage and quote the repair instead. Phoenix hard water adds to the scale: the city's 2025 water quality report puts hardness at 172 to 302 parts per million (City of Phoenix 2025 Water Quality Report). In Phoenix the sewer line from the building to the public main is the property owner's to clean and maintain (Phoenix City Code 28-5), so the camera footage is also your record of the line you own. If you are weighing a cable against a jet, see when hydro jetting beats a cable in Phoenix.

Roots

Jetting Clears Roots. It Does Not Keep Them Out.

A jetter can clear a root mass out of a sewer line. The crack or open joint the roots grew through is still there afterward, and the tree is still looking for water. The camera after the cleaning shows whether the pipe can be sealed, needs replacement or is sound enough for repeat cleanings.

Read whether hydro jetting keeps tree roots from coming back, signs of tree roots in a sewer line and tree roots: repair or replace. If the line is beyond cleaning, see sewer repair.

Commercial Jetting

Jetting for Restaurants and Commercial Buildings

In a commercial building, a recurring clog is lost business. Restaurants, hotels, apartment complexes and retail centers send grease, food solids and heavy use down long lines with several branches, and a cable machine only opens a channel. Jetting cleans the pipe wall along the run, and the second camera pass gives a property manager a record to keep.

The size of the job decides the equipment. On smaller commercial jobs we use our cabling equipment. On larger systems we bring a high-powered jetting machine and a two-person jetting team, because that is what it takes to flush a commercial system fully. We run the jetter from the cleanout locations, pull the grease and sludge buildup off the pipe and push it out to the city main. We do this for restaurants, hotels and retail centers, for warehouses and manufacturing sites, and for property managers who look after several buildings.

  • Kitchen grease lines and floor drains. Grease cools and hardens further down the pipe, which is why lines slow long after the sink. Jetting cleans the line between the kitchen and the grease device and beyond it.
  • Vertical drain stacks and building lines. Multi-unit and multi-story buildings share drain stacks, so one restricted stack can back up several units.
  • Main sewer line. The owner maintains the line from the building to the city main in many cases. See sewer line ownership by city.

Jetting cleans the pipes. It does not replace the pump-out of the grease trap or interceptor, which a licensed pumper does on the city's schedule. See grease trap pumping vs cleaning vs jetting, why a commercial kitchen drain keeps overflowing and why grease gets past an interceptor. We repair, replace and install grease traps and interceptors. See grease trap service and commercial drain cleaning. We can schedule around your hours.

Scottsdale

Hydro Jetting in Scottsdale

HQ Plumbing & Air does hydro jetting in Scottsdale, AZ, for homes from Old Town and McCormick Ranch to DC Ranch, and for Scottsdale restaurants and commercial buildings. The method is the same as anywhere in the Valley: camera first, pressure matched to the pipe, and a second look to prove the line is clear. What is different in Scottsdale is who owns which pipe, how old that pipe is likely to be, and what the city expects from a restaurant's grease lines.

Who owns the line. In Scottsdale the building sewer and the sewer lateral are private up to and including the tap on the public main, and the property owner maintains them (Scottsdale City Code 49-127). Scottsdale Water maintains the main itself. The code asks the account holder to find where a blockage is and what caused it. For a home, when a lateral in the street fails from a cracked pipe or a separated joint, and not from roots, sags or what went down the drain, the city may repair that stretch while its yearly repair fund lasts. A restaurant, office or store pays for cleaning and repair all the way to the main. The city says Scottsdale Water can send a crew to help find where a backup starts (Scottsdale Water: maintenance and troubleshooting). The camera footage from a jetting visit answers the same question: where the blockage sat, what it was, and whether the pipe needs more than a cleaning.

How old the pipe is. Census figures put about 38,000 Scottsdale homes, roughly 27 percent, before 1980, and about 20,000 before 1970 (Census ACS, Scottsdale). The city grew from more than 10,000 people in 1960 to nearly 68,000 by the end of the decade, and the master-planned communities came after 1970. So a 1960s house and a newer DC Ranch house can drain through very different pipe, and they may need very different jetting setups. Scottsdale's water also runs 13 to 17 grains per gallon of hardness by the city's 2024 water quality report, which adds scale inside older lines.

Restaurant grease lines. Scottsdale's Water Quality Department inspects each restaurant's grease traps and interceptors. Under city code, an interceptor rated 100 gallons per minute or 200 pounds or less is completely cleaned by a licensed contractor every 30 days, a larger one every 90 days, and either one sooner at 25 percent full, with logs kept on site for three years (Scottsdale restaurant grease program). A business with no interceptor that causes a sewer blockage or adds to grease buildup in the city sewer can be required to install one (Scottsdale City Code 31-85). Jetting the line from the kitchen to the interceptor, and the lateral beyond it, keeps grease from getting that far. The pump-out itself stays with a licensed pumper. For Scottsdale's water heater permit rule and other local plumbing rules, see our Scottsdale plumber page.

Warning Signs

Signs You May Need Hydro Jetting

Frequent clogs or backups in the same line
Slow or gurgling drains
Grease buildup in kitchen lines
Roots showing on a camera inspection
Odors coming from drains
Several fixtures backing up at once
Whole House

Will Jetting Fix Every Slow Drain in the House?

It will when the problem is the line those drains share. When the tub, the toilet and the kitchen sink all slow down or gurgle at the same time, the blockage is usually in the main building drain or the sewer line to the street. Jetting that line from the main cleanout clears it for every fixture that empties into it.

It will not fix every slow drain on its own. One slow sink usually means a clog in that sink's trap or branch line, which a smaller cable often clears faster. A drain that gurgles with no clog can point to a blocked roof vent. The camera tells us which line is the problem, so you pay to clean the line that needs it. See drain cleaning for single fixtures and sewer camera inspection to find the spot, and camera inspection after jetting for the second look that proves the line is clear.

What Drives the Price

What Affects the Cost of Hydro Jetting

We do not post prices because the line decides them. These are the factors:

  • Pipe size and length. A longer or larger line needs more time and more equipment.
  • Access. A cleanout is quick. No cleanout means more work.
  • How heavy the buildup is. Grease, scale and root masses take different amounts of work.
  • Camera inspection. The look before and after is part of the visit. Sewer camera inspection can also be booked on its own.
  • Timing. An after-hours emergency is a different visit from a scheduled one.

The way to get an exact number is the free estimate. You get the price up front, before any work starts.

Who Needs This

Who can benefit from hydro jetting

  • Homeowners with clogs that keep returning
  • Restaurants and commercial kitchens
  • Property managers and multifamily owners
  • Buyers who found roots on a sewer scope
Scope

What we take on

We handle
  • Camera inspection before and after
  • Hydro jetting of drain and sewer lines
  • Repair of the pipe when cleaning is not enough
  • A free estimate and an upfront price
Not covered
  • Jetting pipe that a camera shows is too fragile
  • Grease trap pump-outs (a licensed pumper does these)
  • City sewer mains
If your line is too damaged to jet, we quote the repair instead.
FAQ

Frequently Asked Questions

Anything else, call (602) 675-1555.

Can hydro jetting damage my pipes?

It can, if the pipe is old or already broken. One jetting equipment maker warns that too much pressure can tear apart a clay line or separate the hubs on cast iron. That is why we run a camera first and match pressure and flow to the pipe. Some pipes, such as Orangeburg, should not be jetted at all.

Is hydro jetting safe for cast iron or clay pipe?

It can be, when the pipe is sound and the pressure is matched to it. Old cast iron and clay can be brittle, so the camera comes first and tells us whether to jet, clean another way or repair the line.

Can you jet a restaurant kitchen line?

Yes. Grease lines, kitchen floor drains and the sewer line beyond the grease device are the most common commercial jetting jobs. Jetting cleans the pipes. The grease trap or interceptor itself is pumped out by a licensed pumper on the city's schedule.

How often should a line be jetted?

There is no one schedule. It depends on what goes down the line, the pipe material and what the camera shows. A restaurant with a grease coating needs a different plan from a home with roots. The camera video after each cleaning is your baseline for deciding when to come back.

How long do the results of hydro jetting last?

It depends on what was in the line. Grease comes back as fast as the kitchen sends it, so a busy restaurant line may need jetting on a set schedule. Roots come back because the crack they grew through is still there. Hard water scale builds slowly. The camera footage after the cleaning shows what was removed and what is left, which is the best guide to when the line needs another look.

Can I keep using water during hydro jetting?

Not on the line being cleaned. The jet sends water and loosened debris down that pipe, so running a sink, a tub or a washer that drains into it can push water back up at the lowest drain. Fixtures on other lines are usually fine. Wait until the technician tells you the line is clear and the second camera pass is done.

What does hydro jetting cost?

The price depends on the pipe size and length, the access point, how heavy the buildup or roots are, whether a camera inspection is needed first, and whether the job is a scheduled visit or an emergency. We give you a free estimate and an upfront price before any work starts.

What is hydro jetting?

Hydro jetting sends high-pressure water through a hose and a special nozzle that scours the full inside of a drain or sewer pipe. The blast cuts and flushes away grease, scale, sludge, and tree roots, leaving the pipe walls clean rather than just poking a hole through the clog.

Read full answer: What is hydro jetting?
What's the difference between hydro jetting and drain snaking?

A drain snake punches a hole through a clog so water flows again. Hydro jetting uses up to 4,000 PSI water to scour the full interior of the pipe, removing grease, scale, and roots a snake leaves behind. Snake for one-time clogs, jet for recurring backups, commercial drains, and grease lines.

Read full answer: What's the difference between hydro jetting and drain snaking?
Does hydro jetting keep tree roots from coming back?

No. Hydro jetting clears roots out of the pipe, but it does not close the crack or joint they grew through, and the tree keeps seeking water. To stop regrowth, seal or replace the pipe, remove the source, or schedule repeat cleanings based on what a camera shows afterward.

Read full answer: Does hydro jetting keep tree roots from coming back?
Grease trap pumping vs cleaning vs jetting: which is which?

Pumping and cleaning are one job on the grease device: remove everything inside, scrape the walls, leave it empty. Jetting is a different job on the pipes: high-pressure water scrubs grease off the drain and sewer lines downstream. Neither replaces the other.

Read full answer: Grease trap pumping vs cleaning vs jetting: which is which?
Service Area

Serving The Entire Phoenix Metro

Our crews deliver hydro jetting across Phoenix and the surrounding Valley. Find your city below:

Ready For A Real Clean?

Call HQ for a free estimate and an upfront price. We offer 24/7 emergency service.