Skip to main content
24/7 Emergency(602) 675-1555
El Mirage Local Amendment

What are El Mirage's grease interceptor requirements?

Verified November 14, 2026
In Short

El Mirage keeps the plumbing code's 500 gallon floor and 30 minute retention for a gravity grease interceptor, but the retention must be approved by the City. An automatic grease removal device must keep separating grease as a gravity interceptor when power is lost, and every interceptor's size, type and location must meet the City's requirements.

Official Source
City of El Mirage: Building Safety (current adopted codes and the Adopted Codes and Amendments PDF)
El Mirage amendments to the 2018 International Plumbing Code, Section 202 (gravity grease interceptor and GRD definitions) and Section 1003.2 (Resolution R23-05-10, City Code 150.001)
“These devices must be able to perform as a gravity interceptor if mechanical or electrical power is lost and provide continuous separation.”
Applies to:
Restaurant owners, tenants, kitchen designers, property managers and plumbing contractors installing or replacing a grease interceptor or automatic grease removal device inside El Mirage city limits
Official fee:
not applicable; the interceptor is part of the plumbing permit and plan review for the job
In force:
2018 International Plumbing Code with El Mirage amendments, adopted by Resolution R23-05-10 (passed May 2023, effective July 1, 2023), since July 1, 2023
Last verified:
November 14, 2026, against the official page

In El Mirage, AZ, a gravity grease interceptor holds at least 500 gallons and must give the kitchen's wastewater at least 30 minutes to separate, and that retention time must be approved by the City. An automatic grease removal device (GRD) has to keep working as a gravity interceptor when its power goes out. And the size, type and location of every interceptor must follow the manufacturer's instructions, the plumbing code and the City's own requirements. El Mirage wrote all three changes into the 2018 International Plumbing Code when it adopted it in 2023.

What does El Mirage's plumbing code say about grease interceptors?

El Mirage enforces the 2018 International Plumbing Code, listed on the City's Building Safety page, with local changes adopted by Resolution R23-05-10 and in force since July 1, 2023. Three of those changes touch grease.

The gravity interceptor definition (Section 202). The model code defines a gravity grease interceptor as a unit of not less than 500 gallons where grease separates by gravity "during a retention time of not less than 30 minutes." El Mirage kept every word of that and added "approved by the authority having jurisdiction" after it. So the 500 gallon floor and the 30 minute floor both stay, and the City has the last word on the retention a design gives.

The automatic grease removal device (Section 202). The model definition of a GRD, a unit that skims grease on a timer or an event without anyone touching it, stays as written. El Mirage added: "These devices must be able to perform as a gravity interceptor if mechanical or electrical power is lost and provide continuous separation." A unit that stops separating when its motor, pump or heater loses power does not meet the definition in El Mirage.

Approval (Section 1003.2). The model code says each interceptor's size, type and location follow the manufacturer's instructions and the code, "based on the anticipated conditions of use." El Mirage added "and pursuant to the requirements of the authority having jurisdiction." The sentence that keeps wastes that need no treatment out of the interceptor stays.

How is El Mirage different from Surprise?

Surprise made nearly the same GRD change and the same kind of approval change in its 2024 amendments, but it struck the 30 minute floor outright, so Surprise's retention time is whatever the City approves. El Mirage kept the floor and layered City approval on top of it. A design that gives less than 30 minutes does not meet El Mirage's definition, even before anyone at the City looks at it. See our Surprise grease interceptor requirements page for the side by side.

What do the key terms mean?

  • Gravity grease interceptor. A large tank, usually buried outside, where hot greasy water slows down and cools so the grease floats to the top and solids settle. El Mirage's floor is 500 gallons.
  • Retention time. How long the water stays in the tank at the kitchen's peak flow. More time means more grease stays behind.
  • Automatic grease removal device (GRD). A powered unit, often under or near the sink line, that skims the grease into a container on its own.
  • Authority having jurisdiction. The office that enforces the code. For a plumbing permit inside El Mirage, that is the City's Development Services building safety staff. The City also runs its own sewer system and wastewater reclamation facility, so what goes down the drain ends up at a City plant.

Who does this cover?

Any business inside El Mirage city limits that sends greasy water to the sewer through an interceptor: restaurants, fast food, school and church kitchens, caterers, bakeries and coffee shops with a dishwasher. It covers a new build, a tenant improvement in a strip center, and the swap of an old interceptor for a new one. Our coffee shop, bakery and bar guide explains which kitchens usually need one.

Quick check: does the design meet El Mirage's code?

QuestionEl Mirage answer
Smallest gravity grease interceptor500 gallons
Retention timeAt least 30 minutes, approved by the City
A GRD that stops separating on a power lossDoes not meet the definition
Who settles the size, type and locationThe manufacturer's instructions, the code, and the City's requirements
Water that needs no treatment (such as rain or clear water)Kept out of the interceptor
Which code edition2018 IPC with El Mirage's 2023 amendments, not the 2024 edition

What does this look like in real life?

A new taqueria in a strip center. The kitchen designer sizes an outdoor gravity interceptor from the fixture list and the peak flow, shows at least 30 minutes of retention, and the plans go to the City for review before anything is dug. The City may ask for more capacity, so the tank size is not final until plan review signs off.

A coffee shop that wants a GRD under the counter. The spec sheet has to show the unit keeps separating grease as a gravity interceptor with the power off. A unit that relies on a heater or pump to separate at all will not pass.

Replacing a cracked interceptor. A like-for-like swap is still a permit job. Bring the old unit's size and the current fixture list, since a menu that grew since opening may need a bigger tank.

What should you do next?

  1. 1Confirm the address is inside El Mirage city limits. Neighbors such as Surprise, Glendale and Peoria each have their own rules, and an unincorporated address goes to Maricopa County.
  2. 2Size the interceptor from the kitchen's fixtures and flow. Our grease interceptor sizing worksheet guide walks through the method, and the design must show at least 30 minutes of retention.
  3. 3Check any GRD's spec sheet for power-off separation before you buy it. Our automatic grease removal device guide explains how they work.
  4. 4Pull the permit and send the design to the City. El Mirage's Building Permits page says permits are required for repair or replacement work on plumbing systems, and applications go through ELM Online Permits.
  5. 5Plan the upkeep from day one. A full interceptor passes grease to the City's sewer no matter how well it was sized.

HQ Plumbing & Air services grease traps and interceptors of all sizes for West Valley kitchens. HQ does not pump grease traps itself. It coordinates a pumping company that subcontracts with HQ, so the pumping can go on one HQ invoice, or the customer can use their own pumper, and HQ's crew works right behind the pumper. When an inspector notes a broken or missing baffle, HQ has the trap pumped of all contents, enters it with a three-person team to meet OSHA confined-space rules, and reinstalls the baffles to code. It then hydro jets the incoming and outgoing lines and camera-inspects them so no grease is left between the building and the trap. See grease trap service or commercial plumbing, and for the water side of an El Mirage job, see El Mirage's backflow installation permit.

What do people get wrong?

  • "El Mirage dropped the 30 minute rule like Surprise." It did not. The 30 minute floor stays, and the City must approve the retention.
  • "Any GRD is fine if the health inspector likes it." In El Mirage it must keep separating as a gravity interceptor with the power off.
  • "The manufacturer's chart settles the size." The City's requirements are part of the approval too.
  • "El Mirage is on the 2024 plumbing code." El Mirage still enforces the 2018 edition with its 2023 amendments.

How Do Other Valley Cities Handle It?

WhereWhat appliesSource
SurpriseSurprise, El Mirage's neighbor, went further: it struck the 30 minute retention floor from the gravity interceptor definition so the retention time is whatever the City approves, and its guidance asks for an outdoor unit of 750 to 2,500 gallons. Its GRD sentence says the same thing as El Mirage's. 2024 IPC.Surprise Local Amendments to the 2024 IPC, Sections 202 and 1003.2 (effective January 1, 2026)
Verified November 11, 2026
GlendaleGlendale, El Mirage's neighbor to the east, writes the upkeep into city code instead: every grease trap and grease, oil or sand interceptor is pumped or cleaned out completely at least every 180 days, the owner keeps three years of records, and enzymes do not replace pumping.Glendale City Code Sec. 33-238
Verified October 4, 2026
PeoriaPeoria sets a 90 day pumping interval for every grease trap and interceptor, or sooner if the Director says so, with three years of records kept at the business and no enzymes or bacteria in place of pumping.Peoria City Code Sec. 25-171 to 25-176
Verified October 4, 2026

This page explains the rule. The official text at the source above governs.

Sources
Talk to a plumber

Need this done to El Mirage code?

We pull the permit when the job needs one and do the work to the code on this page. For restaurants, offices and rental properties, we schedule it around your hours.

  • 24/7 emergency service
  • Licensed and insured
  • Upfront pricing
  • Free estimates
See Grease Trap & Interceptor Service

Commercial Plumbing in Other Cities

More El Mirage Codes and Permits

Related Rules and Questions

Questions About El Mirage Plumbing Code?

We work to code every day across the Valley. Call the dispatcher and we'll tell you what your project needs.