Skip to main content
24/7 Emergency(602) 675-1555
Phoenix sump pumps

Sump Pump Installation in Phoenix

Sump pumps for basements, below-grade rooms and low pits, installed to the Phoenix plumbing code and tested in the pit, with a free estimate and the price first.

Short answer

Sump pump installation in Phoenix means a pump in a covered pit at least 18 inches across and 24 inches deep unless otherwise approved, a check valve, and discharge piping that follows the local plumbing code. It only helps where water collects too low to drain by gravity, such as a basement. HQ Plumbing & Air installs and repairs sump pumps across the Valley.

The rules that apply

Each rule links to the official text we read it from. Cities change these, so check the source before a big decision. Last checked 2026-11-21.

The pit has a minimum size and a cover

Phoenix

A sump pit is at least 18 inches in diameter and 24 inches deep unless otherwise approved, with access, a removable cover that holds the loads where it sits, and a solid floor that supports the pump. Drainage has to reach the pit by gravity.

Source: Phoenix Plumbing Code 2024 (IPC), Sec. 1113.1.2

The discharge line has a check valve

Phoenix

Discharge piping is at least the size of the pump's outlet and carries a gate valve and a full-flow check valve. In one- and two-family dwellings, only a check valve is required.

Source: Phoenix Plumbing Code 2024 (IPC), Sec. 1113.1.4

Where subsoil drains discharge

Phoenix

Subsoil drains discharge to a trapped area drain, a sump, a dry well or an approved location above ground. The subsoil sump is not required to have either a gastight cover or a vent.

Source: Phoenix Plumbing Code 2024 (IPC), Sec. 1111.1

A new pit and new piping take a permit

Phoenix

Phoenix exempts replacing plug-in equipment on an existing permanent outlet, but a permit is required to relocate any valves, pipes or fixtures. A new pit, a new discharge line or a new circuit is not on the exempt list.

Source: Phoenix amendment to 2024 IBC Chapter 1, Sec. 105.2 (electrical and plumbing items)

Does a Phoenix home need a sump pump?

Only where water collects below the level it can drain by gravity. A sump pump lifts that groundwater or drainage up and out. A house on a slab with no room below ground has no low pit for that water, so there is nothing for a pump to do. Our page on whether an Arizona home needs a sump pump explains when one makes sense here.

A sump pump does earn its place in a few kinds of space:

  • A basement or below-grade room. The Phoenix Residential Code requires drains around concrete or masonry foundations that retain earth and enclose a habitable or usable space, discharging by gravity or mechanical means into an approved drainage system. Where gravity cannot do it, the mechanical means is a sump pump. Well-drained ground and sand-gravel soils are the exception.
  • A stairwell, window well or below-grade entry that collects water with nowhere to drain.
  • A low pit in a commercial building, such as a garage floor drain set too low to reach the drain by gravity. See whether a parking garage needs a sump pump or an oil separator.

If water runs in from the yard during a monsoon, look at the grading and drainage around the house first.

Sump pump or sewage ejector?

A sump pump is for clear water. Wayne's manual says it plainly: do not use sump pumps to handle raw sewage. If the water comes from a toilet, shower or washer below the sewer line, the right machine is a sewage ejector in a sealed basin, and it discharges to the sanitary drain. Our page on the difference between a sump pump, an ejector pump and a lift station sorts the three out.

What a sump pump installation includes

  • The pit. At least 18 inches across and 24 inches deep under the Phoenix plumbing code unless otherwise approved, with a removable cover and a solid floor for the pump. Wayne says to set the pump on a solid, level surface, never directly on clay, earth, gravel or sand.
  • The pump. Sized to the water coming in and to how high and far it has to push it. The code asks for a capacity and head appropriate to the use.
  • The float. Clear of the pit wall and the inlet, so it can rise and fall freely. A float that catches on the wall may not start the pump.
  • The discharge line. Rigid pipe at least the size of the pump's outlet, with a check valve so the water in the pipe does not fall back into the pit after each cycle. Wayne requires rigid PVC and no flex hose in a permanent install.
  • The outlet. A grounded GFCI receptacle within reach of the cord. Wayne says not to use an extension cord or surge protector, and to have a licensed electrician add a receptacle if the cord does not reach.
  • The test. The pit is filled with water to check that the pump starts and stops on its own, and that the line carries the water where it should go.

Where can the water go?

Wayne's manual says to install the discharge plumbing according to local, regional and state codes. In Phoenix, the storm drainage chapter of the plumbing code sets these rules, each for its own kind of water:

  • Subsoil drains. Section 1111.1 says subsoil drains discharge to a trapped area drain, a sump, a dry well or an approved location above ground.
  • Storm water and the sewer. Section 1101.3 says storm water shall not be drained into sewers intended for sewage only.
  • Storm water onto a lawn. For one- and two-family dwellings, and where approved, Section 1101.2 permits storm water to discharge onto flat areas, such as streets or lawns, provided that it flows away from the building.

The EPA names sump pumps directly. It lists connections of sources of water such as sump pumps, roof leaders, foundation drains and area drains among the inappropriate connections that can overload a sanitary sewer. Wayne's manual also says to check that the discharge pipe carries the water to a point at least 3 feet away from the foundation.

If the property has a drywell or retention basin, read who maintains retention basins and drywells in Phoenix before you send water to it. Our page on where a sump pump can legally discharge sets the clearwater and sewage ejector rules side by side.

How big a pump do you need?

There is no one horsepower that fits every pit. The size comes from two numbers: how much water flows in, and the total height and length the pump has to push it. A pump that is too small for the water coming in can run nonstop and fall behind. Pump makers such as Wayne publish a chart of flow at each height, and that chart, not the horsepower on the box, is what a pump is sized from. If your pump already runs all the time, see why a sump pump runs constantly.

Backup pumps and alarms

Wayne's manual says an independent high water alarm or backup pump should be used when high water could damage property. A battery backup takes over when the power or the main pump fails, and an alarm tells you the water rose past where the pump should have started. Read whether you need a battery backup and what a sump alarm going off means.

To test the pump, pour a bucket of water into the pit and watch it empty the pit. Wayne also says to replace a tether float switch every two years. Our guide on how to maintain and test a sump pump has the full list.

Repair or replace?

A pump that will not start can have a tripped GFCI, a stuck float or a worn switch rather than a dead motor. Start with why a sump pump is not turning on. Replacing the pump makes sense when the motor has failed, the pump is undersized for the water coming in, or the pit and discharge were never built right in the first place.

What sets the price?

We do not publish prices, because no two pits are the same job. The price depends on:

  • whether there is a pit already, or one has to be cut into the floor;
  • the pump's size and type, and whether a backup pump or alarm goes in;
  • how far and how high the discharge line runs, and where it can legally end;
  • whether a new outlet is needed;
  • whether a permit and inspection apply.

You get a free estimate and an upfront price before any work starts. No hidden fees.

Why call HQ for a sump pump

  • Licensed, bonded and insured, Arizona ROC #355170.
  • A two-year warranty on our workmanship, not covering pipe failures. The pump and parts carry their makers' warranties.
  • 24/7 emergency service, for a pit that is filling while the pump sits still.
  • Family owned, founded by Steve Herzog.

We work across Phoenix, Scottsdale, Tempe, Mesa, Chandler, Glendale, Paradise Valley and the rest of the Valley.

How to book

Call (602) 675-1555 or request service online. Tell us where the pit is, whether the water is groundwater or comes from fixtures, and whether a pump is there now.

FAQ

Phoenix Sump Pump Installation: common questions

Anything else, call (602) 675-1555.

Do I need a permit to install a sump pump in Phoenix?

Swapping a plug-in pump for a new one on the same outlet falls under Phoenix's exemption for plug-in equipment. A new pit, a new discharge line or a new circuit is not on the city's exempt list, so plan on a permit and an inspection for a new installation.

Where can a sump pump drain in Phoenix?

The Phoenix plumbing code sends subsoil drains to a trapped area drain, a sump, a dry well or an approved location above ground, and a separate storm water rule says storm water shall not be drained into sewers intended for sewage only. The EPA lists sump pump connections among the inappropriate connections that can overload a sanitary sewer. Wayne's manual says to install the discharge plumbing to local code and carry the water at least 3 feet from the foundation.

Do I need a 1/2 hp or 3/4 hp sump pump?

It depends on how much water comes in and how high and far the pump has to push it. Pump makers such as Wayne publish a chart of the flow at each height. Pick the pump that moves your inflow at your total height, not the one with the bigger number on the box.

How full does a sump pit get before the pump turns on?

The pump starts when the water lifts its float to the switch-on level. On Wayne's pumps that level is set at the factory: about 9 inches with its vertical float switch and about 13 inches with its tether switch. If the water climbs well past that and the pump stays off, check the outlet and the float.

Does an Arizona home need a sump pump?

Most Arizona homes do not need a sump pump. A sump pump removes groundwater from a basement or crawl space, and Valley homes rarely have a groundwater problem. You may need one if you have a below-grade room, or a lot near a wash or canal. A bathroom below the sewer line needs a sewage pump.

Read full answer: Does an Arizona home need a sump pump?
Sump pump vs ejector pump vs lift station: what's different?

A sump pump moves clear water, like groundwater or storm runoff, and the plumbing code says it handles drainage except raw sewage. An ejector pump lifts sewage from low fixtures inside one building. A lift station does the same job for a whole site or sewer system, with a wet well, two pumps and alarms.

Read full answer: Sump pump vs ejector pump vs lift station: what's different?
Do I need a battery backup for my sump pump?

You need a battery backup if losing your sump pump would flood a room you care about. The main pump stops in a power outage or a pump failure, and a backup takes over. Zoeller recommends one where power outages are likely or a basement is finished. Pump makers also advise a high-water alarm.

Read full answer: Do I need a battery backup for my sump pump?
How do I maintain and test a sump pump?

To test a sump pump, pour a bucket of water into the pit. The pump should start on its own and empty the pit quickly. Do that monthly. Every three months, check the float, check valve, inlet screen and pit for debris. Zoeller says its pumps last 7 to 10 years on average.

Read full answer: How do I maintain and test a sump pump?
Why is my sump pump not turning on?

A sump pump that is not turning on usually has no power, a stuck float, or a failed switch or motor. Check the breaker and GFCI outlet first, then make sure the float can move freely and the pit has enough water to lift it. Unplug the pump before you touch anything in the pit.

Read full answer: Why is my sump pump not turning on?
Why is my sump pump alarm going off?

A steady sump alarm means water in the pit rose past the alarm float, above where the pump should have started. The pump may have lost power, a float may be stuck, or the discharge may be blocked. A short chirp every so often usually means the alarm's backup battery is low, not high water.

Read full answer: Why is my sump pump alarm going off?

Need a Sump Pump?

Talk to a real dispatcher. Upfront pricing before work starts, 24/7 for emergencies.